Description
A finishing coat for epoxy systems possessing excellent chemical resistant properties .
Technical Date
Binder Epoxy polyamine adduct .
Pigment Titanium Dioxide and colour pigments
Colour Grey, other colours available .
Appearance Gloss
No. of components Two
Mixing ratio 4 to 1 by weight .
Specific gravity 1.2 Kg/ litre mixed
Pot. Life at 20ْ C 8 Hours
Solids by volume 74.0 %
Flash point Over 21ْ C
Recommended Thickness 75 micron dry
Coverage Theor. 12 m2 / Kg at 50 micron DFT
Thinner Epoxy thinner – Euxit 501
Drying Time Touch dry :- appr. 1-2 Hours
Dry to handle :- appr. 24 Hours.
Overcoating 24 Hours
Remarks :-
To be applied to an intact epoxy system which is uncontaminated, can be supplied in a limited range of colours.
*Minimum steel temperature for coating 4ْ C (39ْ F) above the dew paint.
*Application below 10ْ C (50ْ F) or where the relative humidity is over 80 % should be avoided
Recommended Surface preparation
This product is designed as a finishing coat to steelwork which has been blast-cleaned and primed with approved products.
prior to the application of this product ensure : the painted substrate is intact and free from contaminates .
*All damaged areas of primer should be rectified and made good to ensure uniformity of system.
*All dust should be removed from the substrate by using clean brushes and/or dry compressed airline.
*Ensure that the substrate is completely dry prior to the application of this product. For added protection additional coats may be applied .
Application Method
The recommended method of application is by airless spray. However, brush or roller may also be used. Spray equipment should be of a type approved by the engineer.
Minimum tip orifice : 0.011
Out put fluid pressure : 120 bar (atm )
The spray fan should be adjusted depending on the nature and the shape of the substrate to be painted in order that overspray can be restricted to a minimum .
Safety :-
During application take normal precautions such as wearing safety, face masks and eye shields.
Adequate ventilation must be maintained when applying this product in confined spaces. 40 m air input per time-unit for each litre of paint applied is recommended.
Observe all statutory local bye laws with respect to health and safety together with the laws governing storage flammable liquid products .
Keep material away from sparks and open flames.
Information of this data sheet is believed to be correct at date of printing. However, since we cannot provide all possible details, the information is given without obligation. In case of doubt our technical advisory service is at your disposal .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EPOXIT 620.pdf
Description :-
A solvent base, two component liquid tar-epoxy resin .
Fields of application:-
It is an anti-corrosion coating material for concrete, plaster, iron and steel. Its is used in sewage structures such as sewage pipes, sewage treatment plants... etc. Also Its is used for the protection of steel structures as sluices, harbor installation, sheet piles, ship-building as underwater coating.
Properties :-
-Excellent water immersion resistance .
-Excellent chemical resistance .
-Durable high build film properties .
-Good application properties.
Specification data : -
Coating Type : Coal Tar Epoxy
- Colour Black – Brown.
- Component ratio 5 paint : 1 Hardener
- Gloss semi – gloss.
- Flash point 45o C .
- Thinner Epoxy thinner.
- Thinner Ratio 5-15 % according to application equipment
- Pot life 6 H at 25o C .
- Shelf life 12 months
- Density 15 kg / cm3 .
- Solid content 75 %
- Theoretical
- spreading rate 5 m2 / Lit (150 mic.)
- Time of touch dry 4 – 5 Hrs.
- Surface preparation All surfaces must be free of oil, grease and moisture before blasting to have white metal equivalent to steel structure painting council SP 10
Mixing and thinning:
Mix the paint and hardener 5 : 1 for 15 min With 5 – 15 % thinner
Application:-
Can be applied by brush, spraying .
Airless spray .
:Nozzel Orifice :approx. 0.48-0.53 mm
0.019 – 0.021 inch.
:Nozzel pressure. : 15 MPA ie.150
Approx. at 2100 psi
Packaging 1 Kg, 10 Kg drums .
Complete cure 7 days .
Re-coating interval 6 Hours min.
5 days max.
Surface preparation:
Cement bound surfaces should be dry, firm, smooth and free of dirt, dust and dirt particles, and additionally free from oil, grease and other impurities which can act against adhesion. If necessary, sandblast, flame scale or grind the top surface.
Iron and steel must be rust and scale free, and free from oil, dust, and other impurities.
Application :-
Procedure for cement bound surface:
-Prime with Epoxit 820 with approximately
-20 % Euxit 501 universal thinner. Material consumption approx. 150- 200 g/m2 .
-If considered necessary, apply filler comprising of:-
-1 Part (by volume) Epoxit 820
-1 part (by volume) quartz sand 0,2 – 0,7 mm.
-0,5 part (by volume) thickness agent (aerosil or sylodex) material consumption approx. 600 kg Epoxit 820 /m2 and mm filler thickness.
-Apply one or two coats Epoxit 820 material consumption approx. 300g/m2 per coating . interval between coating 12-48 hours.
-When a number of coatings are to be made, it is recommended that as a form of control or as a precaution against faulty application each coating applied should be of a different color
Container & size
-Epoxit 820 is supplied in containers of 1 kg, 10 kg, resin and hardener are supplied in correct mix. Ratios.
Colour
Black
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EPOXIT 820.pdfEPOXITE ZR
Zink rich primer
Description
Organic zinc rich epoxy ester base .
Advantages EPOXITE ZR
metal primer is specifically formulated to provide.
Excellent adhesion combined with sacrificial protection to steel surfaces where surface preparation may be less than the ultimate , or where repair of aged zinc rich or galvanized steel surfaces is required.
This primer is an ideal zinc primer because of its :
* Pre-mixed zinc dust .
* Ease of application .
* Excellent adhesion .
* Wide compatibility .
Technical data
Coating type Organic zinc rich epoxy ester
Colour Gray
Flash point 80 degrees F ( 27°C seta flash )
Thinner Xylene
Pot life 8 hours at ( 25°C )
Induction time 15 minutes
Shelf life More than 1 year
Density 1.92 Kg / L
Temperature resistance 121°C dry
Volume of solids 45 %
Theoretical spreading
rate 4.4 m2 / L at 100 microns
Application method Air , airless spray , brush
Drying time At 77 of ( 25°C ) , 50 % RH
To recoat 1 hour
To handle 6 hours
Complies with BS 4652 , 1971 Type 2
Guide surface preparation
Prior to abrasive blasting , remove all grease , oil , salts and moisture .
Round off rough welds and sharp edges and remove weld spatter .
Abrasive blast to commercial blast in accordance to steel structures
painting council sp-6.
Application
Brush and roller - use primarily for touch - up and repair .
Air spray Use an agitated spray pot
Spray gun Similar to devilbiss 510
Fluid tip 070`` to 086`` ( E or D Devilbiss )
Air cap Similar to devilbiss 704
Fluid hose Min. 1/2`` ID and max. length 50 feet
Airless spray Heavy duty 30 to 1 airless pump
Tip size .02`` to .025``
Fluid hose 3/8`` ID and max. 50 feet
Pressure pumps should be at the same level or above the spray gun Keep fluid pressures to a minimum .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EPOXITE ZR.pdfEUCO HARD FLOORS
Surface hardener
Description
EUCOHARD FLOORS is a ready to use surface hardener for coloring and hardening concrete floors .
EUCOHARD FLOORS is al low cost solution to the problem of beautifying floors in light to medium duty industrial , commercia and residential areas .
EUCOHARD FLOORS is made from tough wear resistance quartz aggregate,finely ground alkali - fast and light fast inorganic colour pigment .
Properties
EUCOHARD FLOORS are monolithic bonded with base concrete .
Impact resistant oil and grease resistant .Dense and non porous free from rust stain .
Easy to install .
High abrasion resistant .
Complies with BS 784 1953 , ASTM E 97 , BS 1881 ptu 1970 .
Main purpose
EUCOHARD FLOORS is recommended for :
-Colouring and hardening concrete floors subject to light , moderate and heavy traffic .
-More attractive uniform colour to enhance the appearance of the floor or flat work .
-Shopping malls , motels , garages , schools , cafeterias , side walks drive away , parking lot and residences .
-Work shops , loading ramps , aircraft , hangers , power stations , public buildings and every where , where a high quality floor is demanded .
Application
Place concrete and strike off to level of finished floor . Use bull float or derby to level surface . Allow the slab to bleed . To remove bleed water , drag surface with burlap or rubber base .
After the concrete has stiffed to the point of supporting floating operations , open the surface by hard hand-floating or power floating .Normally a finishers foot print of approx. 8 mm in depth indicates that a slab is ready for power floating . Earlier floating of slab edges by hand is strongly recommended since edges will dry first .
For best results and uniform of thickness Eucohard floors should be applied in two or three shakes using approx. two third the total amount for the first shake .
Immediately after the slab surface has been opened by floating , apply the first shake in a uniform application by hand , spreader or suitable method .
Allow the first shake to remain unworked on the surface until it has absorbed moisture and achieved a dark and uniform colour . Then float with hard or power float immediately after , apply second shake again making application to the edges first .
After second shake has absorbed its moisture float the same manner as out lined .Flat trawling should be done keeping the trowel flat and only after the surface has become dull .
When the surface has sufficiently set , a second and final trawling shall be given to the floor . Continue trawling process until the desired surface finish is achieved . Immediately after the final smoothing apply curing compound or water . Cured floors shall be ready for light traffic after 7 to 14 days
Consumption
Average : 5 kg / m2 .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUCO HARD FLOORS.pdfEUCO - FLOOR HARDENER
Concrete hardener
Description
EUCO - FLOOR HARDENER is a colourless product that provides a denser and harder concrete surface on base of selected silicates .
Main purpose
EUCO - FLOOR HARDENER provides a low cost treatment to eliminate excessive dusting of old concrete and gives a clean hard surface to new floors.
Advantages
EUCO - FLOOR HARDENER is a colourless and harmless material which is applied to cement bound surfaces and will react with the free calcium compounds to seal the pores and provides a denser and harder surface with increased resistance to abrasion . Floors treated with EUCO - FLOOR HARDENER will not be affected when subsequently paintedand will eliminate problems of dusting when concrete surfaces are subjected to heavy traffic . A treatment with EUCO - FLOOR HARDENER will also reduce permeability of concrete to water and other liquids as oil etc. .
Properties
|
Appearance |
Liquid |
|
Specific gravity |
1.4±0.02 |
|
Colour |
Clear |
|
Flash point |
Not applicable |
|
Viscosity |
Approx. 275 mps |
|
Solid content |
40% |
|
Solvent |
water |
Application
The surface to be treated must be clean and free from oil and grease .Dilute 1 part of EUCO - FLOOR HARDENER with 4 parts of clean water and apply in two or three even coats allowing the surface to dry out between two coats . Not more than one day after the final application , any excess solution on the surface must be removed by washing with water EUCO - FLOOR HARDENER may be applied with either brushes or by spray equipment .Best results are achieved by using spray equipment .
Consumption
Consumption will depend upon the porosity of the concrete , but as a guide consumption for old concrete will be approx. 150 gm / m2 and for new concrete approx. 100 gm / m2 .
Remarks
EUCO - FLOOR HARDENER is harmless , never the less we recommend to wear gloves and goggle during work . Avoid contact with skin and eyes . Any spillage must be swilled with water as soon as possible since the product becomes glasshard on drying and it is difficult to remove .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUCOfloor hardener.pdfEUCO - RUSTCUT
Description
EUCO - RUSTCUT is a product to protect iron from rusting and turns rust into a stable chemical compound , through a chemical reaction .
Advantages
It is a protection coat for rusty iron . Due to the chemical reaction .
EUCO - RUSTCUT changes rust into a stable chemical compound and prevents the iron to become rusty again .
Protected iron can be painted with the most used paints .
Mode of application
-the surface must be dry and clean from dirt , oils , and greases.
-old paints must be removed by sandblasting or steel brush .
-After the reaction of Euco- Rust cut the coats become black .
Technical Data
|
Finish |
Hard surface after curing. |
|
Colour |
White/Yellow |
|
Solids by volume |
32% |
|
Specific gravity |
0.99gm/cm³ |
|
T.S.R |
20m/kg (15m dry) |
|
Recommended dry film |
30 microns |
|
Wet film thickness |
24 microns |
|
Dry film thickness |
15 microns |
|
Drying time |
|
|
Surface |
1 hrs (at 25 oC. 60% R.H) |
|
Full cured |
72 hrs (at 25 oC. 60% R.H) |
|
Recoat |
|
|
Min |
1 hr (at 25 oC. 60% R.H) |
|
Max |
5 days (25 oC. 60% R.H) |
|
Thinner |
Tap water. |
|
Shelf life |
Up to 1 year. |
|
Method of application |
By brush and spray. |
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUCORustcut.pdfEUCOSIL
Impregnating agents for the building industry
Description
The EUCOSIL solution is a clear water repellent impregnation which prevents water-chloride ion intrusion (salts) form deteriorating the concrete.
Main purpose
It penetrates deep into the substrate, hydrolyses in the pores and capillaries, condenses and form a hydrophobic zone.
EUCOSIL is used as :
1-Masonry impregnation.
2-Primer for silicone resin and emulsion paints and synthetic resin plasters.
3-Strengthener (e.g. for weathered plaster surfaces and pointing mortars).
4-Protection against moisture induced damage.
5-Provention of soluble salt blooming.
6-Low impairment of the breathing activity.
7-Non-adhesive drying.
8-No visible colour change.
9-High alkali resistance.
Standards
Complies with
ASTM –C 672-84
NCHRP 244 Series II
NCHRP 244 Series II
Application
The impregnating agent can be applied in one or more coats to the dry and absorbent building material.
It is also possible to apply the product by brushing or dipping adjacent surfaces such as doors and windows, nonabsorbent surface, etc should be covered to avoid contact with the impregnating solution.
The quantity of impregnating agent required depends on the absorbency of the building material.
We recommend using a trial surface to determine the suitability and effect of the impregnating solution and the quantities required.
Packing
Drums 1 kg. 4 kg.
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUCOSIL.pdfEUXIT 100
Description
A solvent containing , colour less, two component preparation of liquid epoxy resin with formulated amine hardeners.
Fields of application
EUXIT 100 is used to impregnate and to seal all cement bound surfaces, such as old concrete, fresh concrete, plaster etc., for example, concrete roads, high rise and underground garages, concreted parking areas, factories, aircraft hangars, industrial floors, petrol stations, garages, terraces and balconies.
Product characteristics
EUXIT 100 is an impregnation preparation on clear as water, and has an extremely low viscosity. Because of its high capillary action, it forces itself deeply into the foundation material and covers all pores and capillaries. Cement bound surfaces are thereby sealed against penetration by water solvent substances .The penetration of steam is impeded, but however, is not completely prevented. The impregnated surfaces are hardened, resistance to abrasion and chemicals in considerably improved; concrete becomes resistant to the effects of frost-thawsalt .
Technical data
|
Specific gravity at 20 oC (g/cm³) |
0.9 |
|
Solid content |
30% |
|
Mix ratio (by weight) |
3:1 |
|
Mix ratio (by volume) |
3:1 |
|
Pot life at 10 oC (hours) |
20 |
|
Pot life at 20 oC (hours) |
10 |
|
Pot life at 30 oC (hours) |
5 |
|
Minimum hardening temperature oC |
6 |
|
Bone dry at 20 oC (hours) |
1 |
|
Touch dry at 20 oC (hours) |
Ca.24 |
|
Thorough hardened at 20 oC (days) |
7 |
|
Re-workable at 20 oC (hours) |
Immediately-24 |
|
Pencil hardness |
4H |
|
Abrasive resistance. DIN 52108 (cm³/50 cm²) |
7.4 |
|
Flash point (ºC) |
Over 21 |
|
Shelf life |
Up to 1 year |
Surface preparation
Cement bound surfaces should be free of, all dirt particles, free of oil and grease, and also, if possible, should be dry. Mechanical pretreatment is not normally necessary.
Application Impregnation :
To impregnate concrete of grade BN 300, in general, an amount of 150 to 300 g EUXIT 100/m2 is sufficient, depending on the absorbency of the concrete, the total amount should be applied in 1-3 coating with intervals of about 15 minutes between each (wet on wet). Thereby the best possible depth of penetration and an even matt surface will be obtained. The surface traction will then be only very slightly affected .
Sealing:
In addition to the impregnation coatings, after an interval of 6-24 hours, another coating of EUXIT 100 should be applied.
Consumption approx. 200 g/m2.
Thereby an evenly sealed surface will be obtained. The top surface of the concrete will be resistant to strongly reactive substances.
Remarks
Due the different absorbency of the concrete, different colour of the concrete after the treatment with EUXIT 100 can be possible.
Special Instruction
The product contains solvents ! When working in enclosed places, good ventilation must be provided. Keep away from open fire.
Container Sized and Colour
EUXIT 100 is supplied in containers of 10 kg and 25 kg.Resin and hardener are supplied in correct mix ratios colourless .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUXIT 100.pdf
EUXIT 101
Description
Solvent containing, non-pigmented single component polyurethane based preparation. Hardens in atmospheric humidity.
Main Purpose
EUXIT 101 is used to impregnate, hardens, and seal cement bound surface such as concrete, flooring plaster, as well as wood for example:-
concrete roads, high-rise and underground garages, concrete parking areas, factory stores, aircraft hangers, industrial floors, parquet floors and furniture.
By virtue of its high solids content, it is especially suitable for sealing and impregnating porous concrete surfaces.
EUXIT 101 serves as primer under tar-polyurethane resins and coatings on cement bound and bitumen surfaces.
Product characteristics
EUXIT 101 is a brownish sealant, which has a low viscosity and penetrates well into the capillaries and pores of porous surfaces. When properly hardened it is a ductile elastic, highly abrasive and scratch resistant sealant. It is resistant to diluted alkalis and acids, and also to aliphatic hydro-carbons, such as petrol and oils. Sunlight causes a yellowing. However, the mechanical properties of EUXIT 101 are thereby not affected.
EUXIT 101 is not affected by constant temperature or temperature changes between minus 30 to plus 150oC dry heat.
Technical data
|
Viscosity in 2 mm DIN Beaker (sec) |
70-90 |
|
Specific gravity at 20 oC (g/cm³) |
1.0 |
|
Solid contents (%) |
50 |
|
Pot life at 10 oC (hours) |
10 |
|
Pot life at 20 oC (hours) |
6 |
|
Pot life at 30 oC (hours) |
4 |
|
(strongly dependent atmospheric humidity) |
|
|
Minimum hardening temperature oC |
0 |
|
Bone dry at 20 oC (hours) |
1-4 |
|
Thorough hardened at 20 oC (days) |
2 |
|
Re-workable at 20 oC (hours) |
Immediately-24 |
|
Impact hardness konig (ca.sec) |
150 |
|
Pencil hardness |
4H |
|
Abrasive resistance |
|
|
(Taber (CS 10/1000 U loading (mg) |
15 |
|
Flash point (oC |
Over 21 |
|
Risk classification |
A II |
|
Combustion group (VDE 0165) |
G I |
|
Mak value (mg/m³ air) |
870 |
|
Forwarding packing regulations (EVO) |
KL III a/para/3 |
|
Shelf life |
Up to 1 year |
Surface preparation
Cement bound surfaces should be free of loose dirt particles, oil and grease, and if possible, should be dry. Mechanical preparation is not normally required for impregnation.
Iron and steel must be free of rust and scale, and in addition, free from oil dust, grease and other impurities. If necessary, sand blast.
Asphalt must be firm, dry free of loose particles and protruding material, free from dust, oil and grease. In addition 75% of the aggregate (granulation) should lay free on the top surfaces.
Application Impregnation :
To impregnate concrete grade. BN 300, approximately 50% EUXIT 501 thinner should be added to the EUXIT 101 .
Material consumption 150-300 thinned EUXIT 101.
Depending on the absorption of the surface, the entire amount can be applied in 1-3 coating at intervals of 15 minutes (wet on wet).
Thereby the highest possible depth of penetration and evenly distributed matt top surface will be achieved. Traction grip of the surfaces will thereby insignificantly impaired.
Sealing :
Apart from the so called impregnation coatings, after 6-25 hours interval, a further coating of thinned EUXIT 101 should be applied.Material consumption, approx. 250 g/m2.Thereby an even smooth coating is achieved. The concrete surfaces will be resistant against abrasion .
Priming for jointing :
EUXIT 101 can be used as supplied for jointing on tar-polyurethane. Sufficient should be applied so that a visible film remains on the top surfaces.
Special instruction
The product contains solvents! When working in closed places, good ventilation must be provided. Keep away from open fire.
Container sizes and
EUXIT 101 is supplied in containers of 10 kg and 25 kg
Colour shades
Colourless .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUXIT 101.pdfDescription
Two component epoxy-dispersion, dilutable with water.
Main purpose
EUXIT 150 is particularly suitable for highly abrasion resisting Protective coats, easily cleanable, for
impregnation and sealing of cementicious material medium duty floors, drinking water storage tanks e.g.
Product characteristics
When fully hardened EUXIT 150 is resistant against water, oil, grease,ex haust gases, fuel , alkalis , diluted acids, saline solutions.
Technical data
|
Viscosity at 20 oC cps |
2500 |
|
Specific gravity at 20 oC (g/cm³) |
1.2 |
|
Solid content |
50% |
|
Mix ratio (by weight) |
4:1 |
|
Pot life at 20 oC (hours) |
2 H |
|
Minimum hardening temperature oC |
8 oC |
|
Bone dry at 20 oC (hours) |
4 H |
|
Touch dry at 20 oC (hours) |
15 H |
|
Thorough hardened at 20 oC (days) |
24 H |
|
Adhesion to concrete |
Concrete fracture |
|
Shelf life |
Up to 1 year |
Surface preparation
Cement bound surfaces must be dry, firm, offer good traction, and be free from grout, dust and dirt particles, and, additionally, be free of oil, grease and other impurities which can adversely affect uniform adhesion. If considered necessary the surface should be sand blasted, flame scaled, faced or ground.
Application
First coat EUXIT 150 diluted with approx. 30% water.
Second coat EUXIT 150 non diluted.
Consumption
Two coats approx. 0,3 L / m2 / coat
EUXIT 150 can be sprayed with an airless gun, applied by roller or brushed on.
Container and sizes
EUXIT 150 is supplied in containers of 5 liters, 10 liters, 20 liters and 200 liters .
Colour shades
Resin and hardeners are supplied in correct mix ratios.
Colour shade : 102 light gray .
800 white and other colour by order.
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUXIT 150.pdfEUXIT 50
Description
Solvent free , non-pigmented ,two component preparation of liquid epoxy resin base , with formulated amine hardeners .
Fields of application
EUXIT 50 is particularly suitable for filling cracks and joints of all kinds, for strong jointing of concrete sections, of new concrete on to old concrete ,and iron to concrete .
Because of its low viscosity , EUXIT 50 can be mixed with considerable amounts of mineral filler (aggregates). It is therefore , especially suitable as filler compounds, repair and synthetic mortars for strong jointing , or as inner linings for heavy static loads.Also because of its low viscosity, EUXIT 50 has a good penetration potential on porous surfaces and is therefore most suitable as primers under solvent free coating preparations .EUXIT 50 is a special sealing compound for capillary ,sealing of concrete bearers under asphalt track surfaces .
Characteristics
EUXIT 50 is primarily low viscosity (highly fluid) special mixture with high capillary action , which penetrates into the smallest capillaries and pores. When fully hardened, it is water-and weather-proof ;resistant to waste and sea water, Alkalis , diluted acids saline solutions, greases, fuels and mineral oils .
EUXIT 50 is particularly free of yellowing .
EUXIT 50 is unaffected by constant temperatures and temperature variations in the range from-30oC to + 100oC dry heat, and up to + 50oC wet heat. The mixed preparations can stand up to + 150oC dry heat and up to + 80oC wet heat. For brief periods the mixtures can be subjected to 50% higher temperatures .
Technical date:
|
|
EUXIT 50 |
EUXIT 50 Mortar 1:9 |
|
Viscosity at 20 oC cps |
300 |
--- |
|
Specific gravity at 20 oC (g/cm3) |
1.05 |
2.1 |
|
Mix ratio (by weight) |
3:1 |
--- |
|
Mix ratio (by volume) |
5:2 |
--- |
|
Pot life at 10 oC (hours) |
1 ½ |
10 |
|
Pot life at 20 oC (hours) |
1 |
4 |
|
Pot life at 30 oC (hours) |
¼ |
1 |
|
Minimum hardening temperature oC |
8 |
10 |
|
Bone dry at 20 oC (hours) |
2 |
8 |
|
Thorough hardened at 20 oC (days) |
7 |
7 |
|
Re-workable at 20 oC (hours) |
Immediately |
12-24-12 |
|
Volume shrinkage (%) |
3.5 |
0.35 |
|
Linear shrinkage |
0.3 |
0.03 |
|
Hydrolysis count DIN 53401 |
0 |
--- |
|
Impact hardness konig (sec) |
140-160 |
--- |
|
Pencil hardness |
2 H |
--- |
|
Erichsen indentation (mm) |
2 |
--- |
|
Abrasion DIN 52108(cm3/50 cm2) |
3 |
--- |
|
Compression (N/mm2) |
85 |
120 |
|
Bending property (N/mm2) |
45 |
36 |
|
E-module (N/mm2) |
2800 |
24000 |
|
Breaking tension (%) |
4 |
--- |
|
Revers. Compression at 15 N/ mm2) load (mm/m%) |
0.5 |
0.06 |
|
Glass temperature oC |
57 |
100 |
|
Adhesion to concrete after storage |
Concrete |
Concrete |
|
At temperature changes |
Fracture |
Fracture |
|
Expansion coefficient (X 10-6) |
70 |
20 |
|
Shelf life |
Up to 1 year. |
|
|
Colour |
Colourless |
Colourless |
|
Complies with ASTM D-543. ASTM C 881-87 |
||
Surface preparation:
Cement bound surfaces must be dry, firm, offer good traction and be free from grout, dust and dirt particles, and additionally be free of oil, grease and other impurities which can adversely affect uniform adhesion . If considered necessary the surface should be sand blasted , flame scaled, faced or ground.
Iron and steel must be free of rust and scale free, free of oil, dust, grease and other impurities. The best surface preparation is sand blasting.
Application
Joining cracks :-
Joining cracks and joints in concrete .
See specification sheet "compression of cracks"
Small holes :-
Filler compound for leveling small holes and contractions in horizontal concrete surfaces, for smoothing over sand blasted roughness, and also to join concrete to concrete and iron to concrete. Filler compound to be prepared from :
1 part (by volume) EUXIT 50 (1 liter = 1 kg)
1 part (by volume) fire dried quartz sand 0,06 - 0,2 mm
(1 liter approx. 1,5 kg) .
1 part (by volume) thickening agent
Material consumption approx. 500 - 600 g EUXIT 50 /m2 and 1mm coating thickness .
Cementing fresh concrete onto or with old concrete:
If necessary , sandblast , flame scale or grind the top surface.
Apply EUXIT 50 to the surface to be joined. Minimum consumption :
approx. 500 g / m2Preparing the cement mortar. Water-cement factor maximum 0,6 .Apply the mortar to the still sticky EUXIT 50 and compress. Time between the application of EUXIT 50 and the application of cement mortar from 1/2. up to a maximum of 5 hours at 20oC.
Synthetic resin mortar 1 : 9 - 1 : 15 :
Apply EUXIT 50 as primer Consumption approx.
200 - 300 g/m2 Preparation of synthetic resin mortar .
For coatings of 5-10 mm thickness :
1 part (by weight) EUXIT 50
9 parts ( by weight) according to application, fire dried additives of
7,5 % weight quartz powder (approx. 50)
37,5% weight quartz sand (0,06 - 0,2 mm)
55,0% weight quartz sand (0,7 - 1,2 mm)
Material consumption 150 - 200 g EUXIT 50 / m2 and mm coating thickness, depending on proportion of additives .
For manual application mortar ratio of 1 : 9 is suitable .Mortar which is to be compressed by finisher should have a mixing ratio of 1 : 12 - 1 : 15 of the same screening .
For coatings of 8 - 15 mm thickness :
1 part (by weight) EUXIT 50 and
15 parts fire dried additives of :
1 part quartz sand (0,06 - 0,2 mm)
1 part quartz sand (0,2 - 0,7 mm)
1 part quartz sand (2,0 - 3,5 mm)
Material consumption approx. 150 g EUXIT 50/m2 and mm coating thickness .
For coatings of 15 - 30 mm thickness:
1 part (by weight) EUXIT 50 and
20 parts (by weight) fire dried additives of :
1 part quartz sand (0,06 - 0,2 mm)
1 part quartz sand (0,7 - 1,2 mm)
1 part quartz sand (4 - 8 mm )
Material consumption approx. 100 g EUXIT 50 / m2 and mm coating thickness .
To improve the non-skid properties , a fine sand may be sprinkled (granulation 0,09 - 0,2 mm or 0,2 - 0,7 mm). Best applied with a sand blasting appliance. If repair mortar or synthetic resin mortar have to be coated over with a pigmented preparation such as EUXIT 60 , then the freshly applied mortar must definitely be sprinkled with fire dried quartz sand , granulation 0,2 - 0,7 mm (to improve the intermediate adhesion).
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUXIT 50.pdfEUXIT 55
Description
A solvent free , highly fluid non-pigmented . Two component preparation of liquid epoxy resin base with formulated amine hardener.
Fields of application
Due to its low viscosity , EUXIT 55 can be mixed with a considerable amount of mineral filler (aggregate). It is therefore especially suitable as filler compound , repair mortar and synthetic resin mortar on cement bound surfaces. Because of its low viscosity and its good penetration properties EUXIT IT 55 can be used as a surface primer under solvent free coatings .
Product characteristics
EUXIT 55 when properly hardened is resistant to alkaline solution diluted acids , saline solutions, mineral oil, and aliphatic hydrocarbons and is weather-proof and virtually non-yellowing.
Complies with ASTM D - 543 , ASTM C 881-87
EUXIT 55 is unaffected by constant temperatures and temperature variations in the range of -30oC to 20oC wet heat , EUXIT 55 mortar is resistant to up to + 120oC dry heat and + 50oC wet heat .
Resistance to higher temperatures is possible for shorter periods .
TECHNICAL DATA
|
|
EUXIT 55 |
EUXIT 55 Flow mortar 1:4 |
EUXIT 50 Mortar 1:9 |
|
Viscosity at 20 oC cps |
400 |
--- |
--- |
|
Specific gravity at 20 oC (g/cm3) |
1.06 |
1.8 |
2.04 |
|
Mix ratio (by weight) |
7:3 |
--- |
--- |
|
Mix ratio (by volume) |
2:1 |
--- |
--- |
|
Pot life at 10 oC (hours) |
1 ½ |
2 |
2.5 |
|
Pot life at 20 oC (hours) |
½ |
¾ |
1 |
|
Pot life at 30 oC (hours) |
¼ |
1/3 |
½ |
|
Minimum hardening temperature oC |
8 |
8 |
8 |
|
Bone dry at 20 oC (hours) |
2 |
2 ½ |
3 |
|
Walkable at 20 oC (hours) |
24 |
24 |
24 |
|
Thorough hardened at 20 oC (days) |
7 |
7 |
7 |
|
Re-workable at 20 oC (hours) |
Immediately 24 |
12-24 |
12-24 |
|
Volume shrinkage (%) |
4 |
1 |
0.4 |
|
Linear shrinkage |
0.3 |
0.1 |
0.03 |
|
Hydrolysis count DIN 53401 |
0 |
--- |
--- |
|
Impact hardness konig (sec) |
100-200 |
--- |
--- |
|
Pencil hardness |
H |
--- |
--- |
|
Erichsen indentation (mm) abrasion |
4 |
--- |
--- |
|
a)Tabor (cs 10/100u/1000g (mg) |
70 |
--- |
--- |
|
b)DIN 52108 (cm3/ 50 cm2) |
3 |
9 |
8 |
|
Compression (N/mm2) |
30 |
50 |
70 |
|
Bending property (N/mm2) |
33 |
30 |
24 |
|
E-module (N/mm2) |
300 |
3000 |
9000 |
|
Tensile strength (N mm2) |
24 |
--- |
--- |
|
Breaking tension (%) |
30 |
--- |
--- |
|
Reversible. Compression at 7.5 N/ mm2) |
2.3 |
--- |
--- |
|
Glass temperature oC |
30 |
55 |
70 |
|
Adhesion to concrete after storage |
Concrete |
Concrete |
Concrete |
|
at temperature changes |
Fracture |
Fracture |
Fracture |
|
Shelf life |
Up to 1 year |
||
Surface preparation
Cement bound surfaces must be dry, firm, offer good traction, be free from grout, dust and dirt and additionally free of oil, grease and other impurities with can adversely affect uniform adhesion. . If considered necessary, the surface should be sand blasted, flame scaled, milled or ground.
Iron and steel must be free of rust and scale and should be free from oil, dust and grease and other dirt particles. The best method of preparation is to flame scale or sandblast.
Application small holes:
Filler compound for leveling small holes and contractions in horizontal and vertical concrete surfaces and smoothing over sand blasted roughness.
Filler compound to be prepared from:
1 part (by volume) EUXIT 55 (1 liter = approx. 1 kg)
1 part (by volume) fire dried quartz sand 0,06 - 0,2 mm f
( 1 liter = approx. 1,5 kg)
1 part (by volume) thickening agent (Aerosil or Sylodex)
Material consumption approx. 500-600 g EUXIT 55 and mm coating thickness per m2.
Repair mortar, flow mortar :
For this purpose three parts (by volume) aggregate should be added to so that a good fluid mixture results with enough free resin . There by a primer is not required.
Repair mortar to be prepared from :
1 part (by weight) EUXIT 55 (1 liter = 1 kg)
1 part (by weight) fire dried quartz sand 0,06 - 0,2 mm f
2 part (by weight) fire dried quartz sand 0,7 - 1,2 mm f
Thoroughly mix EUXIT 55 components A and whilst stirring, first ad the finer sand, then the coarse grained sand, and mix well.
Material consumption approx. 450 g EUXIT 55 and mm coating thickness per m2.
Sprinkle the freshly applied coating with fire dried quartz sand, granulation 0,2-0,7 or 0,7-1,2 mm f , according to desired roughness.
Thereby a good skid free traction surface results.
As consequence of this sprinkling of sand, the thickness of the coating is increased by 30-50 %
Synthetic resin mortar :
Apply EUXIT 55 as primer .
Material consumption approx. 200-300 g EUXIT 55/m2.
For coating of 5-10 mm thickness.
1 part (by weight) EUXIT 55
9 part ( by weight) according to application, fire dried additives of
7,5 % weight quartz powder (approx. 50 u)
37,5% weight quartz sand (0,06 - 0,2 mm)
55,0% weight quartz sand (0,7 - 1,2 mm)
Material consumption 140-200 g EUXIT 55 and mm coating thickness, depending on proportion of additives .
For coating of 8-15 mm thickness :
1 part (by weight) EUXIT 55 and
15 part (by weight) fire dried additives of :
1 part quartz sand (0,06-0,2 mm)
1 part quartz sand (0,2-0,7 mm)
1 part quartz sand (2,0-3,5 mm)
Material consumption approx. 150 g EUXIT 55/m2and mm coating thickness .To improve the non-skid properties, a fine sand may be sprinkled (granulation 0,09-0,2 mm or 0,2-0,7 mm) . Best applied with a sand blaster. If repair mortar, flow mortar or coarse mortar have to be coated over with a pigmented preparation such as EUXIT 60 then the freshly applied mortar must definitely be sprinkled with fire dried quartz sand granulation 0,2-0,7 mm(to improve the intermediate adhesion).
Container sizes and Colour:
EUXIT 55 is supplied in containers of 1 kg , 10 kg .
Resin and hardener are supplied in correct mix ratios.
Colourless .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUXIT 55.pdfEUXIT 56
Primer for moist surface
Description
Solvent free, highly fluid non-pigmented, two component preparation of liquid epoxy resin base with formulated amine hardener.
Fields of
Because of its modification, EUXIT 56 can be used as a application primer for moist (not wet) concrete surfaces.
Solvent free coating on epoxy base or mortars can be applied after wards.
EUXIT 56 is highly recommended as a primer to renovate buildings, floors, swimming-pools, tunnels a.s.o.
Product characteristics
EUXIT 56 when properly hardened, is resistant to alkaline solutions, diluted acids, saline solutions, mineral oil and aliphatic hydrocarbons and is weatherproof and virtually non-yellowing.
EUXIT 56 is unaffected by constant temperatures and temperature variations in the range of - 30oC to + 80oC dry heat and up to + 40oC wet heat.
Resistance to higher temperatures is possible for shorter periods.
Surface
Cement bound surfaces can be moist but not wet.
preparation
The surface must be firm, offer good traction, and be free from grout, dust and dirt particles, and additionally be free of oil, grease and other impurities which can adversely affect uniform adhesion. If considered necessary the surface should be sand blasted, flame scaled, faced or ground.
Technical data
Viscosity at 20o C (cps) 800 - 900
Specific gravity at 20oC (g/cm3) 1,03
Mix ratio ( by weight) 7 : 3
Mix ratio ( by volume) 2 : 1
Pot life at 10oC (min.) 60 - 90
Pot life at 20oC (min.) 25 - 40
Pot life at 30oC (min.) 10 - 20
Min. hardening temperature (oC) 8
Bone dry at 20oC (hours) 2
Walkable at 20o C (hours) 24
Thorough hardened at 20oC (days) 7
Re-workable at 20oC (hours) 0 - 24
Volume shrinkage (%) 4
Linear shrinkage (%) 0,3
Compression (N/mm2) elastic (approx. 50)
Bending property (N/mm2) elastic (approx. 50)
Adhesion to damp-concrete after 24 hours
water storage (N/mm2) 3,4
Storage life in months at 20oC 12
Application
EUXIT 56 is applied by brush or roller.
Material consumption : approx. 500 - 600 g/m2 depending on the surface.
Container sizes and colour
EUXIT 56 is supplied in containers of 2 kg, 5 kg and 10kg
Resin and hardener are supplied in correct mix ratios.
Colourless .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUXIT 56.pdfEUXIT 60
Description
A solvent free, pigmented, two component preparation of liquid epoxy resin with formulated amine hardener .
Fields of application
EUXIT 60 is a coating material for cement bound surfaces such as concrete, plaster, asbestos cement, and also for iron and steel. Because & wood it has a very low viscosity, it can be mixed with additives, for example, for flow mortar and filler compounds.
The main fields of application are the floor and wall surfaces which are subjected to considerable chemical and mechanical loads, as in the chemical and textile industries in container and silo construction, in the sewage sector, battery plants, etc.
Product characteristics
When properly hardened EUXIT 60 is very hard, has a good resistance to abrasion with good elasticity. It is weather-proof, water, waste and sea waterproof. Euxit 60 is significant having excellent resistance against organic and inorganic acids, alkalis, mineral oils and many solvents.
EUXIT 60 is resistant to constant temperature and temperature variations From - 30oC to + 100oC dry heat and up to + 60oC wet heat. The mixture preparation (mortars) are resistant up to + 120o C dry heat and up to + 80oC heat. For short periods the mixtures can stand 20 - 30 % higher temperatures. Floor coatings can be cleaned by steam jet.
Technical data
|
Mix ratio (by weight) |
4:1 |
|
Mix ratio (by volume) |
5:2 |
|
Pot life at 10 oC (hours) |
1 ½ |
|
Pot life at 20 oC (hours) |
¾ |
|
Pot life at 30 oC (hours) |
¼ |
|
Minimum hardening temperature oC |
8 |
|
Bone dry at 20 oC (hours) |
2 ½ |
|
Walkable at 20 oC (hours) |
24 |
|
Thorough hardened at 20 oC (days) |
7 |
|
Re-workable at 20 oC (hours) |
5-24 |
|
Volume shrinkage (%) |
2 |
|
Linear shrinkage (%) |
0.2 |
|
Impact hardness konig (sec) |
140-160 |
|
Pencil hardness |
2-3 H |
|
Erichsen indentation (mm) |
1 |
|
Abrasion DIN 52108 (cm³/50 cm²) |
4 |
|
Adhesion to concrete after storage at temperature changes |
Concrete-fracture |
|
Compression strength N/mm² |
80 |
|
Bending property N/mm² |
34 |
|
Tensile strength N/mm² |
23 |
|
E – module N/mm² |
4000 |
|
Thermal expansion ºC-1 |
60X10-6 |
|
Abrasion resistance DIN 52108 |
4 |
|
Sp.G. |
1.4 gm/cm³ |
|
Solids by volume |
98% approx. |
|
Dry film paint thickness |
250 micron |
|
Wet film paint thickness |
250 micron |
|
Theoretical spread rate |
3 m²/kg for 250 M.D.F.T |
|
Complies with ASTM C 881-87-ASTM D-543 |
|
Surface preparation
Cement bound surfaces must be dry, firm offer good traction, be free from grout, dust and dirt and additionally free of oil, grease and other impurities which can adversely affect uniform adhesion. If considered necessary, the surface should be sand blasted, flame scaled, milled or ground. Iron and steel must be free of rust and scale and should be free from oil, dust and grease and other dirt particles. The best method of preparation is to flame scale or sandblast .
Application
Thin smooth coating :
-Prime with EUXIT 60 to which 10% EUXIT 501 thinner has been added. Material consumption depending on absorbency of the surface: 200-400 g/m2.
-After applying the primer, sprinkle with fire dried quartz sand 0,1 - 0,4 mm or 0,2 - 0,7 mm f .
Quantity of sprinkled sand approx. 1,5 - 2 kg/m2 .
-After an interval of 1 day, apply two top coating EUXIT 60 material consumption approx. 500 g/m2 per coating .
-Time interval between the top coatings, maximum 1 day .
Thick coating (smooth or skid free - for coating thickness of 2-4 mm :
-Prime with EUXIT 60 to which 10% EUXIT 501 special thinner has been added. Material consumption according to porosity 200- 400 g/m2.
-Immediately after applying the primer, sprinkle with fire dried
quartz sand 0,1 - 0,4 mm or alternatively 0,2 - 0,7 mm f .
quantity of sprinkled sand - approx. 1,5 - 2 kg/m2.
-After 1 day interval, apply the paving mortar, which should comprise of :
1 part (by volume) EUXIT 60 .
1 part (by volume) fire dried quartz sand 0,1-0,4 or 0,2-0,7 mm agent (Aerosil or Sylodex) .
For horizontal surfaces pour the material and with a spatula or squeegee distribute to the required coating thickness and for airiation and leveling, work over with a rough or spiked roller for vertical surfaces spread the material with a smoothing tool to the required coating thickness. Material consumption 900 g pure EUXIT 60/m2 and mm coating thickness.
-If a slip free surface is required, then immediately sprinkle flow mortar (without thickening agent) with fire dried quartz sand 0,2-0,7 or 0,7-1,2 mm f according to desired roughness.
quantity of sprinkled sand - about 5 kg/m2.
-On the next day, scrape away the excess sand and apply a top coating or EUXIT 60 to which has been added 5% EUXIT 501 special thinner, to ensure an even thin sealing.
material consumption approx. 400 g /m2 pure EUXIT 60 .
Containing procedure for iron and steel:
-Sand blast in accordance with rost point 2.213 (optimum top surface condition peak to valley height approx. 50 u) .
-Apply 3 top coats of EUXIT 60 (until completely free of porosity) .
material consumption 300-400 g/m2 per coating.interval between the coating 5-24 hours at 20oC.
-If longer interval occurs between the application of the coating, or in case old coating have to be renewed, the old surface must be thoroughly cleaned and sanded. There after a new porous free coating must be applied. It is not -sufficient just to re-paint once over.
Inside coating of large containers
When working in enclosed areas, inside containers or in silos, good ventilation must be provided.
Warm fresh air must be pumped in and the stale air must be extracted. Whilst applying coating sufficient heating should be provided so that the walls maintain a minimum temperature of 15oC. it must be at least 5oC above the dew point, so that moisture condensation is avoided between applications of coatings.
After coating and painting work has been completed, a temperature of 25-30oC of the coated walls must be maintained for at least 7 days to ensure that an optimum hardening is obtained .
Containers with high chemical loads should, in addition, be brought up to wall temperatures of 40-50oC for at least three days with the aid of infra-red heaters.
Container sizes and colour shades
EUXIT 60 is supplied in drums of kg and 1 kg .
Resin and hardener are supplied in correct mix ratios.
Colour
102 light sky
601 bluesky
201 beige
302 birk-red
703 light green
705 dark green
other colours available .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUXIT 60.pdfEuxit 80 L.C
Solvent Free Epoxy Coal Tar
Paint System
Descriptions
High build two component polyamine cured epoxy pigmented with selected type of coal tar to give the followings specifications :
Good weather resistance even to chemically contaminated atmosphere.
Good adhesion to different substrate metals, concrete, wood and cement.
Good abrasion resistance and impact. High dry film thickness per one coat without sagging.
Resistant to drainage water and all chemical residuals due to sewage water
Mode of Application
- As an anti corrosive paint for ship painting under water line.
- Sewage water tanks & pipes .
- Oil tanks.
Technical date
:finish :gloss
Colour :Black
Specific gravity :1.25 gm / cm3
% solid by volume : 95%
theoretical spreading rate : 9.5 m / kg (100 Microns)
We film thickness :145 microns
Dry film thickness :135 microns
Mixing ratio
by weight :5 : 1
:K1 : KII
Thinner :Euxit 501 (Euco thinner)
Touch dry :3.0 hrs.
Drying time surface :24 hrs.(at 25ºC 60% RH)
Full cured :7 days.(at 25ºC 60% RH)
Recoat interval min :24 hrs.(at 25ºC 60% RH)
Max :7 days.(at 25ºC 60% RH)
Pot life :30-45 min(at 25ºC 60% RH)
Shelf life :6 months (at 25ºC 60% RH)
Application methods
Brush and roller
-for small areas
-Volume of thinner :0-5%
Surface Preparation Euxit 80 L.C
is applied on clean and dry primed surface or new blasted steel to SA 2.5.
Iron and steel must be free of rust and scales and should be free from oils dust and grease and other dirt particles.
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
Euxit 80 Lc.pdfTar-epoxy resin compound
Description
A solvent free, thixotropic, two component preparation of liquid tar-epoxy resin with modified amine hardeners.
Fields of application
EUXIT 80 is an anti-corrosion coating material for concrete, plaster, iron and steel, especially suitable for sewage works, e.g., for coating sewage pipes, sewage treatment plants, decomposition, etc. Further more also applicable as protective corrosion inhibitor coating material in hydraulic steel construction, such as inhibitor coating for sluices, harbor installations, steel sheet piling. Additionally in ship-building as underwater coating. EUXIT 80 is an excellent cold insulation material in underground construction.
Product characteristics
EUXIT 80 combines the high water-proofing of special tar with the outstanding thermal and chemical properties of epoxy resin. Both components give the hardened coating a high tasticity ductility hardness and abrasion resistance.
EUXIT 80 has an extremely low water absorption, and a good resistance to chemicals, is waterproof, waste and sea waterproof, and has resistance to diluted acids, alkalis and aliphatic hydrocarbons, such as petrol, oil and diesel fuel.
It is not affected by constant temperatures or temperature changes between -30oC and + 80oC .
A wet film thickness of approx. 500 u can be made in one operation with EUXIT 80 .
Technical data
|
Viscosity in 8mm DIN Beaker at 20 oC (sec) |
50-80 |
|
Specific gravity at 20 oC (g/cm³) |
1.48 |
|
Mix ratio (by weight) |
3:1 |
|
Mix ratio (by volume) |
2:1 |
|
Pot life at 10 oC (hours) |
5 |
|
Pot life at 20 oC (hours) |
2 ¼ |
|
Pot life at 30 oC (hours) |
1 ¼ |
|
Minimum hardening temperature oC |
8 |
|
Bone dry at 20 oC (hours) |
8 |
|
Thorough hardened at 20 oC (days) |
7 |
|
Re-workable at 20 oC (hours) |
12-48 |
|
Shore A hardeness |
94 |
|
Impact hardness konig (sec) |
30 |
|
Pencil hardness |
H |
|
Adhesion to concrete after storage |
|
|
Temperature changes |
Concrete-fracture |
|
Shelf life |
Up to 1 year |
|
Water absorption after 21 days at 23 oC |
|
|
a)tet:50x50x1 mm (weight%) |
0.6 |
|
b)DIN 53472 test:50x50x4 mm (weight %) |
0.15 |
|
Weight loss after 28 days at 60 oC |
|
|
a)test thickness : 0.3 mm (weight %) |
5.8 |
|
b)test thickness : 4 mm (weight %) |
0.6 |
Abrasion DIN 52108 CM³/50CM²) |
4 |
|
Complies with BS 5493 RF 3B |
|
Surface preparation
Cement bound surfaces should be dry, firm, smooth and free of dirt, dust and dirt particles, and additionally free from oil, grease and other impurities which can act against adhesion. If necessary, sand blast, flame scale or grind the top surface.
Iron and steel must be rust and scale free, and free from oil, dust, grease and other impurities.
Application
Procedure for cement bound surfaces :
-Prime with EUXIT 80 with approximately 20 % EUXIT 501 universal thinner. Material consumption approx. 150-200 g/m2.
-If considered necessary, apply filler comprising of :
1 part (by volume) EUXIT 80 .
1 part (by volume) quartz sand 0,2 - 0,7 mm .
0,5 part (by volume) thickening agent (Aerosil or Sylodex) material consumption approx. 600 g EUXIT 80 /m2 and mm filler thickness.
-Apply one or two coats of EUXIT 80 material consumption approx. 300 g/m2 per coating .interval between coating 12-48 hours.
-When a number of coatings are to be made, it is recommended that as form of control or as a precaution against faulty application, each coating applied should be of a different colour.
Container sizes and Colour
EUXIT 80 is supplied in containers of 1 kg, 10 kg.
Resin and hardener are supplied in correct mix ratios.
Black , Brown .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUXIT 80.pdfAnti-Corrosive Paint
Description
A solvent containing pigmented two component epoxy resin containing the anti-corrosive pigment zinc-dust.
Main purpose
EUXIT ZNP is used as anti-corrosive paint for iron and steel.
EUXIT ZNP serves as a primer for iron and steel if afterwards a thin synthetic resin coat is applied. In addition
EUXIT ZNP can be used for concrete repair works, by protecting the exposed reinforcement from further corrosion.
Product characteristics
After proper hardening EUXIT ZNP shows a high abrasion resistance and an excellent hardness.
EUXIT ZNP is resistant to fresh, sea- and waste water. In addition
EUXIT ZNP is also good resistant to diluted acids, Alkalis, mineral oils, salt solutions and aliphatic hydrocarbons.
EUXIT ZNP is stable to constant temperatures and temperature changes in the range of -30oC to + 90oC at dry conditions, at wet conditions
EUXIT ZNP is resistant up to 40oC .
Technical data
|
Mix ratio (by weight) |
4:1 |
|
Viscosity in 4mm DIN Beaker 23 oC |
65 |
|
Viscosity (mPas) |
300 |
|
Specific gravity at 23 oC (g/cm³) |
1.7 |
|
Solid content (weight%) |
96 |
|
Pot life at 10 oC (hours) |
4 |
|
Pot life at 20 oC (hours) |
2 |
|
Pot life at 30 oC (hours) |
1 |
|
Minimum hardening temperature oC |
18 |
|
Maximum rel.humidity till bone dry (%) |
90 |
|
Bone dry at 23 oC (hours) |
2 |
|
Time interval for second coat at 23 oC (hours) |
1 |
|
Time to walk over at 23 oC (hours) |
1 |
|
Thorough hardened at 23 oC (hours) |
7 |
|
Complies with ASTM D-520 BS-4652 |
|
Surface preparation
Iron and steel must be free of rust and scale free , and free of oil , dust , grease and other impurities .The best surface preparation is to sand blast iron and steel according to the standard rost 2.213 . The peak - to - valley high should be approx. 50 u .The surface should be according to DIN 55928 part4 .
Application
It is important that the temperature of the surface is always higher than the minimum hardening temperature of EUXIT ZNP In addition the temperature must be 3oC higher than the dew-point in order to avoid any water condensation . The relative humidity should be below 85% .
After EUXIT ZNP is applied , it is necessary to protect the coat from humidity for a period of 5 hours .
In cases where EUXIT ZNP comes in contact with humidity , while the product is not hardened , a colour change (white) will occur on the surface .
The surface will not properly harden in opposite to the underground . if a second coat has to be applied , it is in such cases necessary to remove by sand blasting the unhardened paint
1-EUXIT ZNP used as primer :
-Surface preparation ( ® surface preparation )
-Apply EUXIT ZNP ( sand - yellow ) by roller or brush material consumption approx. 250 gm / m2
-Apply on the following day a second coat with EUXIT ZNP ( red - brown ) by roller or brush material consumption approx. 250 gm / m2
-10 minutes later sprinkle fine - dried quartzsand (0.1-0.5 mm) over the second coat .
-Apply earliest on the following day final top coat
Note : if the final top coat is a solvent containing paint , do not sprinkle quartzsand over the second EUXIT ZNP application .
2- EUXIT ZNP for concrete repair work ( reinforcement ) :
-Surface preparation of the corrosive reinforcement ( ® surface preparation )
-Apply immediately after the surface preparation is made , by brush or roller EUXIT ZNP material consumption approx. 300 gm / m2
-Apply 5 - 24 hours later a second coat of EUXIT ZNP material consumption approx. 300 gm / m2
-Sprinkle 10 minutes later fire - dried quartzsand ( 0.1 -0.5 mm )over the EUXIT ZNP coat .
-Further repair work may be done earliest after 1 day .
Tools can be cleaned with EUXIT 501
Remarks
- EUXIT ZNP is flammable .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUXIT ZNP.pdf