EUCOCOLLE

S B R water proofing and adhesive emulsion for mortar

 

Description          

EUCOCOLLE is a water proofing bonding agent and adhesive emulsion for mortar based on (S.B.R) .

 

Main Purpose      

To achieve considerable adhesion of mortar on concrete surfaces especially for rendering on smooth pre-cast concrete elements .

 

Advantages         

Better and easier workability .Better water retarding properties minimize cracking incidence .Better abrasion and chemical resistance Higher tensile and compressive strengths.

Mortar is more resistant to water after adding EUCOCOLLE .

 

Properties      

Appearance                                         liquid

Specific gravity                                   1,04

solids by volume                                 29 %

Chloride content                                 nil

Compatibility with cement                 all types of portland

          cement.

Shelf life                                             up to 2 years

Complies with ASTM C-631, C-932                 

 

 

 

 

Remarks        

Stir well before use

Instructions For use          

1- Preparatory work            

Subgrade must be sound,  clean and free from traces of  form-oil .Any loose particles and laitance must be removed The surface should be thoroughly wetted before hand until complete saturation of the concrete.

                           

2- Bonding coat

2.1 Equal volumes of cement and clean washed sand ,well

graded from 0-4 mm, are mixed with water and 5-10 %  EUCOCOLLE of cement weight (or ganging solution of 1:1 EUCOCOLLE : water)to a mortar of stiff  consistency .The stiff mortar is vigorously applied with  the trowel to a thickness of not less than approx. 4-5 mm. 

 

2.2 When the bonding coat has set, the next coat is applied on the wet bonding coat surface as a double layer of 7-8 mm thickness .

 

Acrylic water proofing and adhesive emulsion for mortar          

3- Floor topping

3.1 The preparation of the surface follows the same rules as described before .

3.2 The ganging solution consists of equal volumes of EUCOCOLLE and water .

3.3 Equal volumes of cement and sand 0/2 to 0/3 mm are mixed with the above ganging solution to a thin plastic  mortar .The diluted EUCOCOLLE grout is rubbed into the prepared concrete surface with brushes or stiff  broom (apply in strips).

The grout is them evenly trawled on the fresh  diluted EUCOCOLLE grout to the required thickness .

Apply firmly with trowel over the whole surface .Minimum thickness 5 mm .

3.4 Stiff mortar made with 5% EUCOCOLLE is applied in one layer to the still fresh grout .The floor topping should  have a final thickness of  approx. 1,5 cm . The mortar is tamped vigorously and finished with a float .

 

4- Patching and leveling mortar

Surface treatment, thorough wetting ,preparation of the    

EUCOCOLLE bonding coat as well as application of 

further mortar layers are basically the same as for floor

toppings and wall rendering .

 

Remarks        

Curing of all types of mortar .

Rendering, floor topping, patching and leveling mortar etc. .

Should be kept moist for 5 days at least to prevent premature

drying out by wind and sun .

 

Packing               

  In drums containing 20 and 200 kg

Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below

EUCOCOLLE.pdf

EUCOLITE

Waterproofing admixture for mortar

 

Description          

EUCOLITE is a waterproofing admixture based on selected raw materials .

EUCOLITE is available in two types as EUCOLITE L in liquid form and as EUCOLITE P in powder form.

 

Main Purpose      

To achieve a waterproof mortar with high compressive strength and reduced tendency to crack and shrink .For rendering, brickwork mortar, swimming pools, basements ... etc. .

 

Advantages         

Both types of EUCOLITE are chloride-free The water reducing properties enable higher compressive strengths to be obtained at the same workability . Can be used with all types of Portland cement .

 

Properties                    EUCOLITE L             EUCOLITE P

Appearance                  liquid                             powder

Specific gravity            1,05                               --

Bulk weight                  --                                   0.95

Chloride content           nil                                  nil

Compatibility with cement  all types of Portland cement

Shelf life                      up to 2 years                   up to one year,

dry and water

closed

Complies with DIN 1084 - part 1

 

 

 

 

Instructions for use  

External rendering The addition of EUCOLITE L / EUCOLITE P for mortar external rendering will increase the water tightness without impending the breathing of the walls. EUCOLITE L / EUCOLITE P can be used in all types of mortar .

Waterproof  rendering ( subject to water pressure) :

1-Preparation of the surface : the surface must be sound, clean and rough .

Any cracks porous patches and defective areas should be cut and repaired as the work proceeds. Infiltration of water must be stopped with EUCOQUICK .

 

2-   First and second coat : mortar : 1:1 (cement : sand 0/3 mm.) .Each coat approx. 4-5 mm thick taking care to cover the surface completely .Dosage 2% EUCOLITE L / EUCOLITE P of the cement weight .

 

3-   Third and forth coat : mortar 1:2 to 1:3 (cement : sand 0/4 or 0/5 mm) . Each coat 7-8 mm thick .Total thickness of rendering approx. . 2-2,5 cm depending on water pressure .  

Dosage 1% EUCOLITE L / EUCOLITE P of the cement weight . Each coat has to be applied as soon as the former one has set sufficiently .

 

Waterproofing Admixture for Mortar

Dosage 1% EUCOLITE/EUCOLITE P of the cement weight.

Each coat has to be applied as soon as the former one has set sufficiently.

 

4-   Finishing coat: mortar 1:1 rubbed in with float. Use finishing coats without sand only in water tanks, galleries, sewerage systems, and similar constructions .

In rooms exposed to condensation water or heat a finishing coat of lime mortar 5-10 mm thick is recommended (without EUCOLITEL/EUCOLITE P) .

 

Dosage           

EUCOLITE L and EUCOLITE P

2 % of the cement weight

1 kg per bag of 50 kg cement

 

Packing               

In bags containing 20 kg

In plastic drums containing 200 kg .

Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below

EUCOLITE.pdf

EUCOPOR M

Plasticiser for mortar

 

 

Description          

EUCOPOR M is a special plasticiser for mortar based on neutralized vinsol resin .

 

Main Purpose      

To improve workability and trawling properties of sand/cement mortar mixes during application .

 

Advantages         

Strong plastification with water reduction .No bleeding and no segregation .

Frost - resistance to aggressive media .EUCOPOR M entrains a controlled amount of microscopic air bubbles which increase cohesion and provide .Lubrication to the sand particles in the mix, thereby importing workability to the mortar .The air bubbles hold the cement/water matrix at the contact surface which results in improved bond strengths

 

 

 

 

 

Properties           

Appearance                             liquid

Specific gravity                       1,08

Chloride content                     nil

Compatibility with cement     all types of Portland

        cement

Shelf life                                 up to 2 years

 

 

Dosage           

The nature of sand will determine the optimum amount necessary ; a plastering grade will require less and a coarse washed sand .Site trials will best determine the practical rate of addition in each case The rate of addition is generally in the range of :

0,25 % of the cement weight

125gm per bag of 50 kg cement

 

Remarks        

Do not use for concrete .

 

Packing               

In drums containing 20 kg .

Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below

EUCOPOR M.pdf

EUCORAPID

Quick setting admixture

 

Description          

EUCORAPID is a quick setting agent for rapid rendering against moderate to severe water infiltration .

 

Main Purpose      

Used for rapid rendering to isolate and restrict moderate to severe water infiltration on concrete, bricks rock and for all cases where faster setting and early usability is desired or necessary

 

Properties     

Appearance                                         liquid

Specific gravity                                   1,23

Chloride content                                 nil

Compatibility with cement                 all types of Portland

cement

Shelf life                                             up to 1 year

 

 

 

 

Instruction for use

Sealing of moderate infiltration EUCORAPID must only be used with ordinary fresh Portland cement and not with special cements . Prepare the cement paste with EUCORAPID in small quantity and use before setting begins . Pour EUCORAPID in a container, add cement and mix for a few seconds (do not over mix) .

Dilution of EUCORAPID 1 : 0 to 1 : 6 with water .Setting begins after 1/2 to 3 minutes at 20o C .

Apply firmly with trowel over the whole surface . Minimum thickness 5 mm .

 

 -Sealing of severe infiltration and against high pressure 

Apply the EUCORAPID cement paste as above, in such way that water is  concentrated at the points of greatest infiltration .

Insert shortLengths of plastic tube set in EUCORAPID and cement and complete preliminary waterproofing .These discharge pipes prevent the surrounding mortar from being subjected to pressure until properly set .

The application of the waterproof rendering can start as soon as the EUCORAPID mortar is strong enough (6-12 hours) The short lengths of plastic tube should not be removed until at least 24 hours after the application of the waterproof rendering .The holes are then made good with plug of cement and EUCORAPID or if the pressure is severe wit neat EUCOQUICK and cement .

The final coat of the EUCOLITE rendering is then applied over the whole surface making sure that there is at least 1 cm of cover over the plugs .

The preliminary waterproofing with EUCORAPID must always be protected by a normal setting rendering of EUCOLITE or by gunite or concrete .

 

Packing               

In drums containing 10 , 20 and 200 kg .  .

Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below

EUCORAPID.pdf

EUCOSTICK

                 Multi purpose bonding agent (for mortar)

 

 

Description          

EUCOSTICK is an emulsion bonding agent for cement mortar to give many application possibilities

Fields of  application         

1- EUCOSTICK is an additive for cement sand rendering mortar to  achieves maximum adhesion even with smooth surfaces like fair face concrete .

2- A very strong and efficient agent for bonding old and new concrete .

3- Additive for cement screed floor mortar .

 

Advantages         

- Strong bonding to the old floor .

- High resistance to friction and abrasion .

- Achieves minimum thickness for proper leveling .

- Eucostick gives the mortar elasticity and workability with a very low water cement ratio .

 

Properties      

Appearance                                         white liquid

Specific gravity                                   1,06

Chloride content                                 nil

Compatibility with cement                 all types of Portland

cement

Shelf life                                             12 months .

Complies with ASTM C 631. C 932

 

 

 

 

Application   

Surface preparation :-

- Surface must be clean and free from dust, dirt, oils, grease and loose particles .

- Surface must be wet with water before applying EUCOSTICK mortar .

 

Eucostic mortar  

- Prepare the surface as mentioned before .

- A mix of EUCOSTICK and water with ratio 1:5 - 1:7 prepared as a mixing solution to cement and sand to produce the screed or rendering mortar .

- Spread the mortar to the surface using spatula and leave it until it dries out .

 

 

Repair mortar  

- Surface preparation as before .

- Prepare a mix of EUCOSTICK and water 1:3 as a mixing solution to cement sand mortar .

- Add the previous mix to a mix of cement and sand with ratio 1:1 to form the required mortar .For deep holes apply the mortar on many layers .

 

hardener       

3- Surface      

- Surface preparation as before .

- Apply a mix of EUCOSTICK and water 1:4 as a paint to the floors to raise its resistance to friction and abrasion and to be dust proof .

Consumption

Generally the rate of addition of EUCOSTICK is 5-10 % of cement weight according to the purpose or 2.5 - 5 kg for every 50 kg bag of cement .

 

Packing               

In drums of 200 kg .

Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below

EUCOSTICK.pdf