CESO-PLASTER
Thin Coating for Waterproofing
Description
CESO-PLASTER is a ready to use Coating for Waterproofing of different kinds of surfaces such as cement brick ... etc..
CESO-PLASTER is based on cement with carefully graded fine aggregates in combination with selected admixtures .
Main Purpose
Thin coating for rigid surfaces waterproofing .Due to its high quality ,CESO-PLASTER offers many application possibilities as for instance for :
external waterproofing against ground moisture , seeping and subsoil water , swimming pools , water reservoirs , .... etc. .
Advantages
CESO-PLASTER is ready to use in powder form , only water or a mix of water and EUCOCOLLE has to be added for working .
CESO-PLASTER forms after application impermeable layer under positive and negative water pressure .Extremely good adhesion to sound surfaces , extremely high workability , and easy to repair .
Properties
Appearance powder
Bulk weight approx. 1,4
Specific gravity approx. 2,9
Chloride content nil
Colour Gray or white
Shelf life up to one year well closed
and dry stored
Complies with ASTM C - 580,E - 149, C- 190, DIN 52-108
Application
EUCOCURE BR may be applied with either hand or spray equipment .Wash equipment with clean water immediately after using .
Avoid contact with skin or eyes .For new concrete EUCOCURE BR should be applied immediately after the final trawling .Old concrete should be thoroughly cleaned before treatment to allow EUCOCURE BR to penetrate .
Consumption
Approximately 1 kg for 1 sq. meter .
Instructions for use
-The surface which is to receive the CESO-PLASTER has to be clean and free from oil , grease and laitance .
-If needed (Depending on the surface and the expected adhesion) a first coat of EUCOCOLLE / WATER in a ratio 1 : 1 - 1 : 3 should be applied by a brush or roller .
-CESO-PLASTER should be mixed with water to a stiff consistency , the mixing ratio in the range of 1:1 – 2:1 (CESO-PLASTER / WATER) .
-Thorough mixing is essential .Add dry mix to water , not vice versa .
-The mix can be made by a mixer e.g. with a propeller and a drilling machine.
Thin coating for waterproofing.
To insure a very good adhesion specially in case of waterproofing of precast concrete (e.g. fare face concrete) , EUCOCOLLE should be mixed with the previous mix with a ratio of 5 : 1 CESO-PLASTER / EUCOCOLLE apply the first coat of ceso-plaster by roller or brush .
Note
Mix the plaster from time to time to prevent a settle down of the solids
-Apply the second coat of CESO-PLASTER by roller or brush after the first coat is hard enough (Min. Waiting time 4 hrs.)
-For a highly protection against high water pressure third coat of CESO-PLASTER may be applied using the same way .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
CESO plaster.pdfEUCOPREN
Thixotropic Sealing Material
Product
Solvent free , thixotropic sealing material with a bitumen-rubber
Description
EUCOPREN is an air-drying one component sealing material .When properly dries out it becomes waterproof and permanently elastic .
Fields of Application
Sealing material for walls , kiln bed-plate etc… EUCOPREN is an excellent cold insulation material in underground constructions with a permanent elasticity to cover cracks .
Product Characteristics
EUCOPREN is resistant against diluted chemicals but not against mineral oils , diesel etc. .
.
Technical Data
Appearance pasty , thixotropic
Specific gravity 1,08
Min. . drying temperature + 2oC to + 40oC
Bone dry approx. 2 h
Thorough hardened approx. 2 - 3 days
Consumption per m2 approx. 3 kg
Temperature resistance -25o up to + 100oC
Storage life in months at 20oC 12 month protected
against frost.
Surface Application
Cement bound surfaces should be dry ,firm , of good traction and free of dust and dirt particles , and additionally free from oil , grease and other impurities which can act against good adhesion .If necessary , sand blast , brush or grind .
Application
EUCOPREN is supplied ready for use and is applied with trowel or spatula .The surface must be clean , sound and free from loose particles Surface can be damp but not wet .Material consumption approx. 3 kg/ m2 .
Colour
Black .
Packing
Containers of 20 kg & Drums of 200 kg .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
EUCOPREN.pdfISOCOAT 500 F
Waterproofing paint
ISOCOAT 500 F
An elastomeric , water proofing paint recommended for painting on roof tiles , building façade , swimming pools and water reservoirs .
Advantages
1- Protects the buildings from weather conditions all year long.
2- Considerable sun ray reflection , so prevents raising temperature of the buildings during summer .
3- ISOCOAT 500 F could be applied by roller as textured and decorative finishing inside building entrances , kitchens and bathrooms .
4- Applicable on different kinds of surfaces like wood , concrete , steel bricks and asbestos .
5- Due to its elasticity , it can withstand elongation up to five times the original applied length which allow it to cover
building cracks up to 2 mm crack width .
6- ISOCOAT 500 F is a waterproofing paint and resistible to diluted acids, alkalies , salts and sea water .
7- High resistance to UV rays fungi and bacteria.
8- ISOCOAT 500 F is a cold applied paint , which is available in several colours .
9- When dry it can withstand weather conditions which leads to fungus growth or bacteria .
Technical date
Density (gm/cm3) 1,3 - 1,25
Main Drying temperature 5oC
Temperature resistance -10- + 100oC
Shelf life at 20oC 12 months
Complies with ASTM D - 4887,D - 4541
Application
1- Stir well before use .
2- The surface must be clean and free of dust, dirt , grease or oil .
3- Dilute ISOCOAT 500 F by 50% water for the first coat .
4- Apply the second coat with 10% water dilution or without .
5- A layer of fiber glass or industrial textile could be installed between the two coats as reinforcement .
Coverage
1 kg for 2-4 square meters according to the surface nature , number of coatings and rate of dilution .
.
kinds of fungi and bacteria which is resistable by Isocoat 500 F :
Achromobacter Sp. Aspergillus Sp.
Aeromonas Sp. Botrytis Sp.
Alcaligenes Sp. Candida Sp.(Yeast)
Bacillus Sp. Paecilimyes Sp.
Escherichia Sp. Paecilimyes Sp.
Flavobacterium Sp. Rhodotorula Sp. .(Yeast)
Klebsiella Sp.
Proteus Sp.
Pseudomonas Sp.
Packing
1 kg , 5 kg , 20 kg drums .
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
ISOCOAT 500 F.pdfISOCOAT 500
Waterproofing paint
Description
An elastomeric , water proofing paint recommended for painting on roof tiles , building façade , swimming pools and water reservoirs .
Advantages
1- Protects the buildings from weather conditions all year long.
2- Considerable sun ray reflection , so prevents raising temperature of the buildings during summer .
3- ISOCOAT 500 could be applied by roller as textured and decorative finishing inside building entrances , kitchens and bathrooms .
4- Applicable on different kinds of surfaces like wood , concrete , steel bricks and asbestos .
5- Due to its elasticity , it can withstand elongation up to five times the original applied length which allow it to cover building cracks up to 2 mm crack width .
6- ISOCOAT 500 is a waterproofing paint and resistiable to diluted acids, alkalies , salts and sea water .
7- High resistance to UV rays .
8- ISOCOAT 500 is a cold applied paint , which is available in several colours .
Technical date
Density (gm/cm3) 1,3 - 1,35
Min Drying temperature 5oC
Temperature resistance -10- + 100oC
Shelf life at 20oC 12 months
Vis 20000±5000 mpa*s
PH 8.5±1
S.C / weight 57± 1
Solid cont./volume 43.5± 1
Tensile strength N/cm³ 490
Elongation at break (%) 460
Complies with ASTM D - 4887,D - 4541
Application
1- Stir well before use .
2- The surface must be clean and free of dust, dirt , grease or oil .
3- Dilute ISOCOAT 500 by 50% water for the first coat .
4- Apply the second coat with 10% water dilution or without .
5- A layer of fiber glass or industrial textile could be installed between the two coats as reinforcement .
Consumption
1 kg for 2-4 square meters according to the surface nature , number of coatings and rate of dilution
Packing
1 kg , 5 kg , 20 kg drums
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
ISOCOAT 500.pdf
Description
-Solvent free , cold applied water-proofing based on rubber bitumen complies with international standards
Fields of Application:
-RUBBERSEAL is a sealing material for walls and kiln beds
-RUBBERSEAL is an excellent cold insulation material in underground contraction with a permanent elasticity to cover cracks .
-RUBBERSEAL specially recommended for the water-proofing of roofs , footings , basements , swimming pools , bathrooms ,water tanks...etc
Advantages
-RUBBERSEAL forms after drying an impermeable membrane to insure complete waterproofing .
-RUBBERSEAL is very elastic material after drying , can withstand elongation till seven times the original length to cover any cracks and surface defects .
-RUBBERSEAL has a low viscosity with a very high penetration potential to fill the whole surface's pores before forming the elastic membrane .
- RUBBERSEAL adheres the styrofoam and vinyl to the surfaces strongly .
- RUBBERSEAL is resistant to diluted chemicals .
- RUBBERSEAL does not affect the human health so, it can be use without any precautions .
Complies with DIN 18195 part 2, BS, 2782 part 3 .
Properties
Specific gravity 1,04
Min. drying temp (+2oC) to + 40oC
Bone dry approx. 2 H .
Through hardening approx. 2-3 days
Temperature resistance -25oC up to + 100oC
Storage , life in months 12 at 20oC
Surface Preparation:
Cement bound surfaces should be clean ,firm, of good traction and free of dust and dirt particles , and additionally free from oil , grease and other impurities which can act against good adhesion. If necessary ,sand blast, brush or grind surface can be damp but not wet .
Application
RUBBERSEAL is supplied ready to use and is applied with brushes , rollers or sprayers. Two coats are recommended for waterproofing purpose the interval between the two coats is at least four hours . Material consumption approx. 1-1.25 kg/m2
N.B Topseal coat has to be applied as a primer before the Rubberseal.
Colour
Black
Packing
Containers of 20 , 200 kgs
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
RUBBERSEAL.pdfCold applied bitumen emulsion for water proofing
Description
Solvent free, liquid bitumen emulsion consisting of a combination of special water emulsifying agents conforming to international standards.
Fields of application
For all waterproofing purposes on all types of surfaces exposed to water like concrete, metal, wood , and others. Some typical applications are:-
-Foundations, retaining walls and basements, giving a prot
-ection against water infiltration as well as chemical attack from the soil's detrimental salts.
-Roofs and floorings in bathrooms and all areas needing protection from probable infiltration of water
Advantages
-Can be used on damp surfaces and not necessarily a dry one.
-Easy to apply without any heating thus economical in cost and labor.
-Relative short time for the reaching of the final waterproofing properties after application. This is due to the fact that the product does not rely on the evaporation of the emulsion medium for final properties but on the breaking up of the emulsion upon contact with the surface to be water-proofed and after the required time for the penetration of the infinite bitumen particles (1 to 15 microns) into the porous surface such as concrete, bricks or the like has elapsed.
-The product can be diluted with water up to 1:10 (Topseal : water) to allow adjustment with the different conditions and to obtain a higher degree of penetration into the surface.
-The product is odorless thus allows comfortable working conditions and doesn't need special ventilation.
-The final water-proofing layer is highly resistant to chemicals and acids except sulfuric acid and organic solvents.Complies with DIN 18195 part 2.
Properties
S.G. at 25o c 1.058 ± 0.07
PH at 25o c 8.08 ± 0.05
Solid content 35%-37% ±0.1
Elasticity 100%
Min. drying temp. +2oc to +40oc
Bone dry approx. 2H
Through hardening approx. 2-3 days
Storage life at 20oc 12 months
Method of Application
-The surface to be water-proofed is thoroughly cleaned from dirt and other impurities.
-A primer coat is applied of Topseal after dilution with water 1:1 using ordinary painting tools that has been wet before use.The dilution is increased in case of highly porous surfaces or when using a spraying equipment.
-One or two coats are then applied, without any dilution of the product, on the primer coat after its color has turned from brown to black meaning that the breaking of the emulsion and the coagulation of the particles is complete.
This takes approximately from 20 to 30 min. depending on the nature of the treated surface.
Coverage
As a water-proofing coat 750-1000 gm/m2
As a protective coat 250 gm/m2
Packing
Drums of 5kg , 20kg , 200kg
Your web browser doesn't have a PDF plugin. Instead you can download it by clicking the file below
Topseal.pdf